Altronix T2MK3F8ADQ kit consists of Trove2 enclosure and TM2 Mercury/Altronix backplane with 24VDC @ 6A power supply/charger, 12VDC voltage regulator, eight (8) PTC protected output dual input/output network access control module and eight (8) PTC protected dual input/output power distribution module. This kit also accommodates various combinations of Mercury/Lenel* boards for up to eight (8) doors in a single enclosure. Trove simplifies board layout and wire management, reduces installation time and labor costs.*Also compatible with these authentic Mercury partners:AccessNsite, Avigilon, BadgePass, BluBox, Feenics, Genetec, Identicard, IMRON, Johnson Controls, Kastle, Keri Systems, Lenel/S2, LockState, Maxxess, Midpoint Security, NLSS, Open Options, Panasonic Video Insight, Quintron, RS2, Schneider Electric, Vanderbilt
Features
eFlow6NB Power Supply/Charger
Input
- Voltage: 120VAC, 60Hz. 3.5A
- Input Fuse: 5A / 250V
Output
- Voltage: 24VDC
- Current: 6A continuous
- Auxiliary: 1A (unswitched)
- Other: Overvoltage protection. Filtered and regulated
Battery Backup
- Capacity: 7AH / 12VDC (Up to 2 within enclosure). 40 AH / 65 AH (requires separate enclosure)
- Type: Sealed lead acid or gel type
- Fuse Rating: 10A/32V
- Failover: Upon AC loss, instantaneous
Supervision
- AC Failure: Form “C” contacts
- Battery: Form “C” contacts
- Low DC Power Shutdown: Shuts down DC output terminals if battery voltage drops below 70-75% for 24V units. (depending on the power supply). Prevents deep battery discharge
Indicators LED
- Input: 120VAC is present
- DC Output: Powered
- Battery: Discharged or not connected
LINQ8ACMCB Networked Access Power Controller
Input
- Two (2) Independent Low Voltage Inputs:
- – Input 1: 24 VDC from eFlow6NB power supply
- – Input 2: 12 VDC from VR6 voltage regulator
- Input PTC: 9A
Outputs
- PTC protected outputs
- Any of the eight (8) PTC protected power outputs are selectable to follow power Input 1 or Input 2
- Individual outputs may be set to OFF position for servicing
Output PTCs:
- 2.5A
Programming Features:
IEight (8) Programmable Outputs:
- – Fail-safe, fail-secure or auxiliary outputs
- – Input controlled or manually controlled through software
- – High (over) and low (under) voltage and current monitoring by output
- – Multiple outputs may be programmed to be triggered by a single input
- – Battery back-up by output
Eight (8) Programmable Trigger Inputs:
- – Normally open (NO), Normally colsed (NC) or Open collector sink inputs
- – Wet Input (5VDC – 24VDC) with 10k resistor
- – Any combination of the above
Other Programmable Trigger Inputs:
- – Monitor power supply(ies) input for voltage and currect limits (high/low)
- – Input and output current calibration, Programmable timer events
- – Programmable user levels, Enable or disable alerts by type
- – Programmable alert reporting delay
Indicators (LED)
- Green AC LED: indicates AC trouble condition
- Green BAT LED: indicates battery trouble condition
- Green FACP LED: indicates FACP disconnect is triggered
- Flashing Blue Heartbeat LED: indicates network connection
- Individual OUT1 – OUT8 Red LEDs: indicate outputs are triggered
- Individual Voltage LEDs: indicate 12VDC (Green) or 24VDC (Red)
VR6 Voltage Regulator
Input
- Voltage: 24VDC from eFlow6NB
Output
- Voltage: 12VDC
- Current: 6A continuous
- Other: Surge suppression
Indicators LED
- Input: 24VDC is present
- Output: Powered
PDS8CB Dual Input Power Distribution Module
Input
- Voltage: 12VDC from VR6 and 24VDC from eFlow6NB
- Input PTC Rating: 9A
Outputs
- Voltage: 12VDC and/or 24VDC
- Any of the eight (8) power outputs are selectable to follow power Input 1 or Input 2
- Individual outputs may be set to OFF position for servicing
Outputs Ratings
- PTCs: 2.5A
Indicators (LED)
- DC Output: Eight (8) individual output LEDs
- Green: 12VDC
- Red: 24VDC
Environmental
Temperature
- Operating: 0° C to 49° C (32° F to 120° F)
- Storage: – 20° C to 70° C ( – 4° F to 158° F)
Relative Humidity
- Relative Humidity 85% +/- 5%
BTU/Hr (approx.):
- 145 BTU/Hr
Reviews
There are no reviews yet.